ZEEKR 7X Roof Rack Installation Instructions

The ZEEKR 7X roof rack is one of the most popular accessories for owners who need additional cargo capacity for camping, road trips, bicycles, skis, or roof boxes. This guide provides a complete step-by-step installation tutorial, including crossbar orientation, lock cover installation, length adjustment, and safety checks.

Many ZEEKR 7X owners purchase a roof rack but are unsure about the correct installation process. This guide explains the complete installation procedure, common mistakes, and important safety tips to help you complete the installation quickly and correctly.

Although this tutorial focuses on the ZEEKR 7X roof rack, the installation method is also applicable to our shark-fin style roof racks designed for other models, including the Geely EX5, Geely Starray EM-i, ZEEKR 7GT, and similar vehicles. Please note that while the installation procedure is the same, the dimensions of each roof rack are model-specific.

Step 1: Identify the Correct Crossbar Direction

Before installation, it is important to determine the correct orientation of the crossbars.

As shown in Image , the front section of the crossbar is thicker, while the rear section is thinner. The aerodynamic shape is similar to an aircraft wing, designed to reduce wind resistance and noise during driving.

When installing the roof rack:

• The thicker side (Position B) should face the front of the vehicle.

• The thinner side (Position A) should face the rear of the vehicle.

Installing the crossbars in the wrong direction may increase wind noise and reduce aerodynamic performance.

Step 2: Install the Plastic Lock Covers Correctly

One of the most common causes of wind noise is incorrect installation of the plastic lock covers.

Many users mistakenly believe that the crossbars themselves generate excessive wind noise. In reality, improperly installed lock covers often create gaps that produce noise while driving.

Each lock cover is marked:

• L = Left side

• R = Right side

To determine the correct side, sit in the driver's seat and look forward:

• The left side of the vehicle uses the L cover.

• The right side of the vehicle uses the R cover.

Ensure that each cover is fully seated and securely locked into position.

Step 3: Verify the Crossbar Length

The front and rear crossbars are different lengths.

• The longer crossbar must be installed at the front.

• The shorter crossbar must be installed at the rear.

In addition, the crossbar length can be adjusted using the screws located at both ends.

Many customers initially think the roof rack is too short after unboxing. In most cases, the crossbars simply need to be adjusted to the proper length before installation.

Before tightening all hardware, adjust the crossbars to match the vehicle's mounting points and ensure a proper fit.

Final Inspection

After installation is complete:

1. Firmly push and pull the roof rack in multiple directions.

2. Check that there is no movement, looseness, or abnormal noise.

3. Confirm that all brackets fit tightly against the vehicle without visible gaps.

4. Ensure all screws and locking mechanisms are securely tightened.

A properly installed roof rack should remain stable and silent during normal driving conditions.

Safety Tips for Daily Use

To ensure safe operation, please keep the following recommendations in mind:

• Be aware that the overall height of your vehicle increases after installing a roof rack.

• Pay attention to height restrictions when entering garages, tunnels, and parking structures.

• Secure all cargo properly before driving.

• When carrying heavy loads, avoid sudden acceleration, braking, or sharp turns.

• For optimal safety and stability, we recommend maintaining speeds below 120 km/h (75 mph), especially in strong crosswinds.

Installation Video Tutorial

For a clearer demonstration of the installation process, please refer to the complete installation video below. Following the video together with this guide will help ensure a smooth and successful installation.

https://youtube.com/shorts/kXk3GtnD61o

Conclusion

Installing a ZEEKR 7X roof rack is straightforward and typically takes only a few minutes. By following the correct installation steps and paying attention to crossbar orientation, lock cover placement, and crossbar length adjustment, you can enjoy a secure, stable, and quiet roof rack system.

If you are looking for additional ZEEKR 7X accessories, feel free to explore our collection or contact EVSTITAN for assistance.